ANDEROL 5220 XEP
Synthetic Gear and Bearing Lubricant Product Data Sheet
ANDEROL 5220 XEP is a synthetic based, high performing gear lubricant to be used in industrial
equipment. It was designed to withstand heavy loads and severe conditions resulting in very good
micro pitting resistance. The PAO based product gives superior advantages to the mineral oil
based products, especially with regards to low pour point, oxidation stability and energy
consumption.
ANDEROL 5000 XEP range is available in the grades ISO VG 150, 220, 320, 460, 680 and 1000.
Meets or exceeds the requirements of:
ANSI/AGMA 9005 (table 3)
AISE 224 (formerly USS 224)
DIN 51.517
Cincinnati P-59
ADVANTAGES / BENEFITS COMPATIBILITY APPLICATION
Excellent oxidation and thermal stability
Wide operating temperature range
Lower maintenance costs
Excellent load carrying ability
Extended lubricant life
Improved cleanliness
Excellent anti wear & EP properties
Very good rust and copper corrosion
prevention
Compatible with petroleum oils, therefore
allowing minimal effort to changeover
The following seals, paints and plastics are
recommended for use in contact with Anderol
Company Synthetic Lubricants. Materials not
recommended are also shown. For more
information on other materials see our
‘Compatibility Guide’.
RECOMMENDED :
Viton, High Nitrile Buna N, Teflon, Epoxy Paint,
Oil-Resistant Alkyd, Nylon, Delrin, Celcon, PBT
NOT RECOMMENDED:
Neoprene, SBR Rubber, Low Nitrile Buna N,
Acrylic Paint, Lacquer, Polystrene, PVC, ABS
Particularly suited for gear applications
exposed to extreme service conditions
All types of enclosed gear drives
Bearings, including plain rolling elements
and antifriction types
Enclosed gear cases and speed reducers
FOR MORE INFORMATION PLEASE REFER TO THE RELEVANT MATERIAL SAFETY DATA SHEET
APPROVALS / REGISTRATIONS ANDEROL BV
Punterweg 21 A
6222 NW MAASTRICHT
The NETHERLANDS
Tel No.: +31 (0)43 352 41 90
Fax No.: +31 (0)43 352 41 99
www.anderol-europe.com
This information is furnished without warranty, representation, inducement, or license of any kind except that it is accurate to the best of OUR knowledge or obtained from sources believed by
ANDEROL to be accurate. ANDEROL does not assume any legal responsibility for use of reliance upon it. Only Chemists or chemically qualified lab technicians should carry out tests. Before using any
chemicals, read its label and Material Safety Data Sheet.
PROPERTIES TEST METHOD ANDEROL 5220 XEP
Appearance @ 20°C
Viscosity @ 40°C, cSt
Viscosity @ 100°C, cSt
Viscosity Index
Density @ 15°C, kg/l
Total Acid Number, mg KOH/g
Flash Point, °C
Pour Point, °C
Foam , Sequence I,II ml
Micro pitting Resistance Test
FZG Gear test, Pass Stage
Four Ball Wear,1200 rpm, 75°C, 40 kg
Four Ball Weld, kg
Copper Corrosion, 100°C
Steel Corrosion, deionisedwater
Steel Corrosion, seawater
Oxidation characterizing of extreme pressure lubricant:
● Viscosity increase (%)
● Precipitation Number (ml)
visual
ASTM D-445
ASTM D-445
ASTM D-2270
ASTM D-1298
ASTM D-664
ASTM D-92
ASTM D-97
ASTM-892
FVA,54/11
DIN/ISO 14635-1
ASTM D-4172
ASTM D-2783
ASTM D-130
ASTM D-665A
ASTM D-665B
ASTM D-2893
ASTM D-91
Clear Yellow Liquid
221.8
24.5
138
0..899
0.5
248
-45
10
High
14
0.35
250
1a
Pass
Pass
-1.36
0 |
